[. . . ] ENGLISH MODEL Special Notes FCC Radiation Exposure Statement This device complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. It must not be co-located or operating in conjunction with any other antenna or transmitter. This device must accept any interference received, including interference that may cause undesired operation. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles. [. . . ] Notes: ● Refer to the operation manual of the equipment to be connected. — Connecting via this method may disable TV internal speakers. — In some cases, a small background noise could emit from the sound bar, when you use the headphone connection with a TV-Set. In such case, please change the connection to the HDMI/ARC or RCA-connection. This effect depends on the used TV-Brand, model and age, and it is not a quality matter from the sound bar. Caution: ● Remove the battery if the sound bar will not be used for a long period of time. — Installing the battery incorrectly may cause the sound bar to malfunction. — Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Notes concerning use: ● Replace the battery if the operating distance is reduced To turn the power on Press the ON/STAND-BY button on the sound bar or the remote control. — The power turns on and the subwoofer indicator turns blue. If the power does not turn on, check whether the AC power cord is plugged in properly. — The system will automatically power on if TV or similar component which supports HDMI CEC, is turned on. To set the sound bar to stand-by mode: Press the ON/STAND-BY button again on the main unit or the remote control and the subwoofer indicator turns red. Notes: ● A slight audio delay after TV is turned ON does not mean that the system is faulty. — “AQUOS speaker is enabled” message will be displayed if SHARP LCD TV does not detect HT-SB60 during power on. However the message “AQUOS audio with AQUOS LINK is enabled” will be displayed soon as HT-SB60 is detected. vCR DVD player Subwoofer To HDMI (TV ARC) input terminal Place the system as shown. Remove the protective film covering the sound bar and subwoofer before turn on the system. to HDMI OUT (TV ARC) output terminal Stand To HDMI input terminal To HDMI output terminal Sound Bar Connecting a TV , or DVD player , etc. Method 2 This connection is for HDMI TV without ARC (Audio Return Channel). To HDMI input terminal TV To audio output terminal DVD, Blu-ray disc player or similar System connections Make sure to unplug the AC power cord before making any connections. Subwoofer To audio output terminals To Headphone terminal To HDMI output terminal or To HEADPHONE terminal Audio signal Blu-Ray/ DVD player/Digital Tuner Sound Bar Sound Bar To HDMI OUT (TV ARC) output terminal To HDMI input terminal To select HDMI 1, 2 or TV ARC function (Source): Press SOURCE button repeatedly until “HDMI 1”, “HDMI 2” or “TV ARC” appears on the display, or press TV ARC button on the remote control to select the TV ARC. [. . . ] The sound bar will enter the power stand-by mode automatically if no signal is detected after the preset time has elapsed. Signals other than DOLBY DIGITAL, DTS, Linear PCM cannot be recognized. Output HDMI™ output: (audio/video support up terminal to 1080p) x 1 Input terminal Analog input (AUDIO IN): x 1 500 mV / 47 kohms Optical digital input (OPTICAL): Square type x 1 HDMI input: (audio/video support up to 1080p) x 2 Type 2 Way speaker system 2 -1/4" (5. 5 cm) Soft Dome Maximum 160 W input power Rated input 80 W power Impedance 4 ohms Volume auto fade-in If you turn off and on the sound bar with the volume set to 80 or higher, the volume starts at 40 and fades in to the last set level. [. . . ]